Anti-corrosion deck edge overhang

  • TAB-R-2011-141 Drip Edges and Shingles - GAF May 27, 2011 ... Shingles should be installed over the drip edge a minimum of 3/8” (9 ... Make sure the drip edge is adequately fastened to the underlying deck a minimum ... If there is a gutter edge, make sure the shingles overhang the inside...

  • Wood Decking Wood Decking - This page shows you how to lay decking, best decking material, and the ... Once installed, the first board should overhang the front of the deck framing by ... The idea is to leave 1.5" hanging over the edge of the deck framing.

  • How Far Can Decking Extend Past a Joist? | Professional Deck ... Mar 1, 2009 ... Allowable overhangs can range from none to as much as 4 inches, ... the load placed on the edge of decking that's offset from the joist below.

  • Lecture 15B.10 In addition to the load carrying structures that make up the bridge deck, bridges ... bearing systems; finishes; expansion joints; parapets; anti-corrosion protection ..... The fascia are built on the deck edge and perform several functions (Figure 29): ... allow access to both exterior and underside of the overhangs (Figure 31).

  • Constructing cavities for wall claddings[PDF 2.3 MB] provided along the bottom edge of the cavity. .... claddings as this may lead to corrosion of the cladding (refer to E2/AS1 Paragraph. 9.6.9.2). In these .... At roofs or decks, finish the wall cladding a minimum of 35 mm above the surface of the roof or ... The gap must be at least 5 mm to get an anti-capillary break. Figure 16:...

  • 3rd edition, amendment 5 erratum 2 replacement pages - Building ... Table 18D: Corrosion protection to lintels 115 .... horizontally from external face of wall cladding to outer edge of overhang, including fascias ... (7) Excluding drip edge. (8) Excluding drip edge. Membrane roofs and decks ... Anti-capillary gap.

  • Quality Edge | steel siding, roofing and accessories - Arcat Oct 13, 2016 ... TruCedar's outer shell is both anti-corrosive and extremely abrasion resistant .... while maximizing the architectural integrity of your overhangs. ... (For areas under a deck see QE's InsideOut® water catching soffit system.)...

  • Glossary of Commercial Construction Industry ... - ProofRock ANTI-WALK BLOCKS – Elastomeric blocks that limit lateral glass movement in the ... BACK NAILING - The practice of nailing roofing felts to the deck under the overlap, .... CORROSION - The deterioration of metal by chemical or electrochemical .... the side wall, or the lower edge of the part of a roof that overhangs a wall.

  • NZ Metal Roof and Wall Cladding Code of ... - Roofing Industries Feb 6, 2010 ... A flashing covering the edge of the roof cladding at the gable end of a roof ... (b) A slight convex curve of a surface, such as in a roof deck. ... The partial or complete protection of a metal from corrosion by becoming the cathode .... An external roof gutter attached to a roof overhang or the lower edge of a roof.

  • Master Rib Installation Manual - Union Corrugating In addition, the oversized anti-siphoning channel on the under-lap provides ... a metal roof which does not have a plywood or other deck beneath it is not ... Remove any loose metal shavings left on the roof surface immediately to prevent corrosion. ... Allow an overhang a minimum of 1” at the eave to provide for a drip edge.

  • Come aboard USS Gerald R Ford (CVN 78), the newest aircraft carrier Nov 8, 2017 ... Hiding under scaffolding, covered in anti-rust primer, the Ford has just ... being placed further aft, resulting in enormous overhangs on both sides. .... The deck edge was once lined with encapsulated life rafts, now all removed.

  • Guide to Standards & Tolerances 2007 Decks and balcony freeboard outside windows and doors. 49. 3.07 ...... An overhang of 0 mm is permissible if the minimum edge distance for both the bottom ... Any corrosion of metal wall cladding is a defect. 5. 32 .... Anti-capillary break.

  • Packaging Guidelines & Labels - ATA Freight High and low humidity can result in condensation or corrosion, and it can greatly reduce the ... Anything overhanging the pallet edges will be subjected to impacts that can result in ... Select pallets with closely spaced pallet deck boards; Never exceed the rated .... Anti-static peanuts should be used for electronic items.

  • 5V Crimp Panels - Metal Roofing Material as it could cause water stains and in some cases corrosion, damaging the appearance of ... Anti-Siphon Channel ... Frames, purlins, decks and fasteners must be designed to resist all loads .... Install panel, overhanging edge of eave trim by 1”.

  • Prescriptive Deck Guide - City of Poulsbo PRESOR'IPTIVE RESIDENTIAL WOOD DECK CONSTRUCTION GUIDE. CONTENTS .... Edge distance and spacing requirements are based on '/2" diameter ... Flashing shall be corrosion-resistant metal [R7038] ... length of the overhangs. .... anti. _ Xyg. : _ _ a.n. : _ _ m m. : _ y _\"\' _ a ifiwmi _ HNV. W 1 it L=O mow =.

  • 2.6 Installing Integra Lightweight Concrete Flooring - Resene ... Similarly for normal domestic decks the deck joists should be chosen from the ... If on the short edges the panel overhangs a floor joist it must be cut back so ... All reinforcing exposed on cut panels should be coated with anti-corrosion agent.

  • Lecture 15B.10 In addition to the load carrying structures that make up the bridge deck, bridges ... bearing systems; finishes; expansion joints; parapets; anti-corrosion protection ..... The fascia are built on the deck edge and perform several functions (Figure 29): ... allow access to both exterior and underside of the overhangs (Figure 31).